Most basement gyms fail on one number: the ceiling. A standard basement ceiling is 8 feet, which is 96 inches. But the number that matters is not the drywall. It is the lowest duct, beam, or pipe in the spot where the rack will stand. Measure that first, and the rack choice gets easy.
This guide compares four racks we sell at IRONBAY Fitness, all with real heights that fit under a standard 8 foot basement ceiling. No guessing. Just measure, compare, and pick.
Key Takeaways
- Measure to the lowest duct, beam, or pipe, not to the drywall. That lowest point is your real ceiling.
- An 8 foot ceiling is 96 inches. A rack at 87.5 inches leaves 8.5 inches of room above it.
- All four racks below are under 88 inches tall, so all four fit a standard 8 foot basement.
- Height is only half the question. Check the width and depth too, and leave room to walk around the rack and load plates.
- If you plan to do pull-ups on the rack, make sure you have headroom above the pull-up bar, not just above the frame.
Step 1: Measure Your Real Ceiling
Grab a tape measure and check three spots: the middle of the room, each corner where the rack could go, and under every duct and beam in that area. Write down the smallest number. That is your ceiling height for this purchase.
Then subtract the rack height. If the result is less than a few inches, pick a shorter rack or a different spot in the room. A rack that fits with zero room to spare will fight you on every install step.
Step 2: Compare Four Racks That Fit
| Rack | Height | Width x Depth | What it is | Price |
|---|---|---|---|---|
| Eyries R1 Functional Trainer | 87.5 in (2222 mm) | See product page | 2-in-1 functional trainer | $1,750.00 |
| Eyries R1 S Functional Trainer with Smith Machine | 87.5 in (2222 mm) | See product page | 3-in-1: functional trainer, Smith machine, power rack | $2,400.00 |
| Eyries R1 Ultra All-in-One Functional Trainer | 86.7 in (2202 mm) | 65.1 in x 57.9 in | 5-in-1: functional trainer, Smith machine, power rack, lat pulldown, low row | $4,250.00 |
| IRONBAY N1017 All-in-One Functional Trainer with Smith Machine | 86.6 in (220 cm) | 86.6 in x 59.1 in | Smith machine, dual pulleys, lat pulldown, low row, pull-up bar, dip station, landmine | $1,890.00 |
Under a 96 inch ceiling, the Eyries R1 and R1 S leave 8.5 inches above the frame, the Ultra leaves 9.3 inches, and the N1017 leaves 9.4 inches. That is real breathing room, not a tight squeeze.
Step 3: Pick By How You Train
Pick the Eyries R1 if you want cables plus a rack, and nothing more. It is the simplest of the four and the easiest to place. It gives you dual cable training and a power rack in one frame, at the lowest price of the group. See the Eyries R1 Functional Trainer.
Pick the Eyries R1 S if you want a Smith machine too. Same 87.5 inch height as the R1, but it adds a Smith machine and a power rack to the functional trainer. Dual 220 lb weight stacks and a heavy duty 3 in x 3 in 11-gauge steel frame. See the Eyries R1 S Functional Trainer with Smith Machine.
Pick the Eyries R1 Ultra if you want one machine to do it all. It is the 5-in-1: functional trainer, Smith machine, power rack, lat pulldown, and low row. 86.7 inch height, dual 220 lb weight stacks, and a 65.1 in x 57.9 in footprint. If floor space is tight but you want every station, this is the one. See the Eyries R1 Ultra All-in-One Functional Trainer.
Pick the IRONBAY N1017 if you want the lowest height and the widest station set for the price. At 86.6 inches tall it is the shortest of the four, with dual 150 lb weight stacks, a 2:1 pulley ratio, a Smith machine, a dedicated lat pulldown and low row station, a pull-up bar, dip handles, and a landmine attachment. Note the width: at 86.6 inches wide it needs the most floor space of the four, so measure your wall first. See the IRONBAY N1017 All-in-One Functional Trainer with Smith Machine.
One honest note: the three Eyries racks are listed as PreOrder with an ETA of mid-December 2026. If you need a rack sooner, check the N1017 first.

© IRONBAY Fitness. Images not for commercial use.
Three Mistakes to Avoid
- Measuring only the middle of the room. Ducts run along walls, right where racks go. Measure the exact spot.
- Forgetting plate loading space. You need room on the sides to slide plates on and off. A rack that fits the wall but leaves no side room is a daily annoyance.
- Buying height you do not need. A taller rack is not a better rack. In a basement, the rack that fits with room to spare wins.
FAQ
Will an 87.5 inch rack fit my 8 foot basement?
Yes, if your lowest point is a true 96 inches. 96 minus 87.5 leaves 8.5 inches. Measure the lowest duct or beam first, because that number, not the drywall, decides it.
What if my basement ceiling is under 8 feet?
Measure the exact lowest point and compare it to the rack height in the table above. If the gap is under a few inches, move the rack to a spot with more clearance, or pick the shortest rack here, the N1017 at 86.6 inches.
Do I need extra room above the rack for pull-ups?
Yes. The frame height is one thing, and your head above the pull-up bar is another. If pull-ups matter to you, check that you can hang from the bar without hitting the ceiling or a duct.
Which rack takes the least floor space?
The R1 footprint is 50.8 in x 54.1 in, the most compact of the four. The N1017 is the widest at 86.6 in, so it needs the most wall.
Are these racks only for basements?
No. They work in any home gym with enough ceiling height. The point of this guide is that basements, with their ducts and beams, are where height matters most.
Shop online now at IRONBAY Fitness, Calgary.
Updated October 29, 2026.


